ath79: Add support for OpenMesh A60
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi (11n)
* 3T3R 5 GHz Wi-Fi (11ac)
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x ethernet
- eth0
+ Label: Ethernet 1
+ AR8035 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as WAN interface
- eth1
+ Label: Ethernet 2
+ AR8031 ethernet PHY (SGMII)
+ 10/100/1000 Mbps Ethernet
+ used as LAN interface
* 1x USB
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This commit is contained in:
Sven Eckelmann
Adrian Schmutzler
parent
3394af677c
commit
eaf2e32c12
|
|
@ -48,6 +48,7 @@ netgear,wnr2200-16m|\
|
|||
netgear,wnr612-v2|\
|
||||
ocedo,koala|\
|
||||
ocedo,raccoon|\
|
||||
openmesh,a60|\
|
||||
openmesh,mr600-v1|\
|
||||
openmesh,mr600-v2|\
|
||||
openmesh,mr900-v1|\
|
||||
|
|
|
|||
|
|
@ -0,0 +1,8 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qca9558_openmesh_a60.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "openmesh,a60", "qca,qca9558";
|
||||
model = "OpenMesh A60";
|
||||
};
|
||||
|
|
@ -0,0 +1,180 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qca955x.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
chosen {
|
||||
/delete-property/ bootargs;
|
||||
};
|
||||
|
||||
aliases {
|
||||
serial0 = &uart;
|
||||
led-boot = &led_status_green;
|
||||
led-failsafe = &led_status_green;
|
||||
led-running = &led_status_green;
|
||||
led-upgrade = &led_status_green;
|
||||
label-mac-device = ð0;
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
status_blue {
|
||||
label = "blue:status";
|
||||
gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
status_red {
|
||||
label = "red:status";
|
||||
gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_status_green: status_green {
|
||||
label = "green:status";
|
||||
gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
watchdog {
|
||||
compatible = "linux,wdt-gpio";
|
||||
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
||||
hw_algo = "toggle";
|
||||
/* hw_margin_ms is actually 300s but driver limits it to 60s */
|
||||
hw_margin_ms = <60000>;
|
||||
always-running;
|
||||
};
|
||||
};
|
||||
|
||||
&usb_phy1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <40000000>;
|
||||
|
||||
/* partitions are passed via bootloader */
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x000000 0x040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x040000 0x010000>;
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
label = "custom";
|
||||
reg = <0x050000 0x060000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@b0000 {
|
||||
label = "inactive";
|
||||
reg = <0x0b0000 0x7a0000>;
|
||||
};
|
||||
|
||||
partition@850000 {
|
||||
label = "inactive2";
|
||||
reg = <0x850000 0x7a0000>;
|
||||
};
|
||||
|
||||
art: partition@ff0000 {
|
||||
label = "ART";
|
||||
reg = <0xff0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
status = "okay";
|
||||
|
||||
phy-mask = <0x6>;
|
||||
|
||||
phy1: ethernet-phy@1 {
|
||||
reg = <1>;
|
||||
eee-broken-100tx;
|
||||
eee-broken-1000t;
|
||||
};
|
||||
|
||||
phy2: ethernet-phy@2 {
|
||||
reg = <2>;
|
||||
eee-broken-100tx;
|
||||
eee-broken-1000t;
|
||||
at803x-override-sgmii-link-check;
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
pll-data = <0x82000101 0x80000101 0x80001313>;
|
||||
|
||||
mtd-mac-address = <&art 0x0>;
|
||||
|
||||
phy-mode = "rgmii-id";
|
||||
phy-handle = <&phy1>;
|
||||
|
||||
gmac-config {
|
||||
device = <&gmac>;
|
||||
rgmii-enabled = <1>;
|
||||
rxd-delay = <3>;
|
||||
rxdv-delay = <3>;
|
||||
txd-delay = <0>;
|
||||
txen-delay = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
ð1 {
|
||||
status = "okay";
|
||||
|
||||
pll-data = <0x03000101 0x80000101 0x80001313>;
|
||||
|
||||
mtd-mac-address = <&art 0x6>;
|
||||
|
||||
qca955x-sgmii-fixup;
|
||||
|
||||
phy-handle = <&phy2>;
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
|
||||
mtd-cal-data = <&art 0x1000>;
|
||||
mtd-mac-address = <&art 0x0>;
|
||||
mtd-mac-address-increment = <2>;
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
|
@ -170,6 +170,7 @@ ath79_setup_interfaces()
|
|||
comfast,cf-e120a-v3|\
|
||||
comfast,cf-e314n-v2|\
|
||||
compex,wpj531-16m|\
|
||||
openmesh,a60|\
|
||||
openmesh,om2p-v4|\
|
||||
openmesh,om2p-hs-v4|\
|
||||
plasmacloud,pa300|\
|
||||
|
|
|
|||
|
|
@ -98,6 +98,7 @@ case "$FIRMWARE" in
|
|||
caldata_extract "art" 0x5000 0x844
|
||||
ath10k_patch_mac $(mtd_get_mac_binary art 0xc)
|
||||
;;
|
||||
openmesh,a60|\
|
||||
openmesh,mr1750-v1|\
|
||||
openmesh,mr1750-v2)
|
||||
caldata_extract "ART" 0x5000 0x844
|
||||
|
|
|
|||
|
|
@ -65,6 +65,7 @@ platform_do_upgrade() {
|
|||
jjplus,ja76pf2)
|
||||
redboot_fis_do_upgrade "$1" linux
|
||||
;;
|
||||
openmesh,a60|\
|
||||
openmesh,mr600-v1|\
|
||||
openmesh,mr600-v2|\
|
||||
openmesh,mr900-v1|\
|
||||
|
|
|
|||
|
|
@ -1628,6 +1628,16 @@ define Device/openmesh_common_256k
|
|||
openmesh-image ce_type=$$$$(OPENMESH_CE_TYPE) | append-metadata
|
||||
endef
|
||||
|
||||
define Device/openmesh_a60
|
||||
$(Device/openmesh_common_64k)
|
||||
SOC := qca9558
|
||||
DEVICE_MODEL := A60
|
||||
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct kmod-usb2
|
||||
OPENMESH_CE_TYPE := A60
|
||||
SUPPORTED_DEVICES += a60
|
||||
endef
|
||||
TARGET_DEVICES += openmesh_a60
|
||||
|
||||
define Device/openmesh_mr600-v1
|
||||
$(Device/openmesh_common_64k)
|
||||
SOC := ar9344
|
||||
|
|
|
|||
Loading…
Reference in New Issue